|
||
|
Junior Member
  
加入日期: May 2001
文章: 906
|
ABIT NF7北橋電壓修改有譜了∼
國外網站看到的
http://www.xtremesystems.org/forums...p?postid=108459 原來連結，在蠻下面的∼ 不過跟我看的8RDA不太一樣∼ 8RDA北橋電壓修改 不過NF7也是在上面那兩個點銲一個可變電阻嗎？ 原發文者沒說要用幾歐姆的....... |
|||||||
2003-03-08, 01:27 AM
#1
|
|
|
Advance Member
加入日期: Nov 2002 您的住址: 中壢
文章: 377
|
幫忙推
希望有讀電子科系ㄉ大大們來幫忙 |
||
|
2003-03-08, 01:51 AM
#2
|
|
|
Junior Member
加入日期: May 2001
文章: 906
|
引用:
感激兄台相助∼ |
|
|
2003-03-08, 02:03 AM
#3
|
|
|
Amateur Member
 加入日期: Jan 2002
文章: 32
|
ohm->歐姆
|
|
2003-03-08, 11:36 AM
#4
|
|
|
Junior Member
加入日期: May 2001
文章: 906
|
引用:
這個我知道∼ 我是想請問要用幾歐姆的...... |
|
|
2003-03-08, 11:50 AM
#5
|
|
|
Amateur Member
加入日期: Jan 2002
文章: 32
|
引用:
你是說哪個連結的哪個圖呀? 我看到的都有寫幾歐姆耶...@@ 我看錯個了嗎 |
|
|
2003-03-08, 12:33 PM
#6
|
|
|
Junior Member
加入日期: May 2001
文章: 906
|
引用:
其實都一樣！ 只不過第一個連結我把圖單獨連出來...... 你不會看到8RDA那個吧？ |
|
|
2003-03-08, 12:48 PM
#7
|
|
|
Amateur Member
加入日期: Jan 2002
文章: 32
|
我看的是文章,因為你說蠻下面的,我只看了下面兩個,再上面一個才是你說的...@@
我看他說他用50k,不過應該用10k就夠了,因為他調到4.xk 就在那張圖上面有說,他是說完才貼圖的 |
|
2003-03-08, 01:05 PM
#8
|
|
|
Junior Member
加入日期: May 2001
文章: 906
|
引用:
找到了！ 這一段 The VDD mod is easy money. The 6520 IC just under the AGP slot, I hooked up a 50k ohm resistor to pin 6 to ground. I think the 50k is an overkill but thats what I used. It actually reads 4.16k ohms right now. I assume a 10k VR would work fine. You measure the VDD off of a mosfet that is near the IC. I personally soldered a wire to the mosfet leg so I could have easy access to read the voltage, it would be impossable to measure when the agp card is in place. 感激！ 那就是用一個可變電阻，接在他上面標示的兩隻腳囉？ 他還有接出來用電表測量電壓？ 不過好像說當AGP插著時，是量不出來的？ 晚點去試試看∼ 謝謝你的回應！ |
|
|
2003-03-08, 03:03 PM
#9
|
|
|
Amateur Member
加入日期: Jan 2002
文章: 32
|
應該是吧...我自己也沒改過,不敢給你掛保證...
I personally soldered a wire to the mosfet leg so I could have easy access to read the voltage, it would be impossable to measure when the agp card is in place. 這句話應該是指他是焊了一條線所以能輕易的量測電壓,否則當顯示卡插上去的時候沒辦法量到. |
|
2003-03-08, 03:59 PM
#10
|
|
