這裡也有一個在賣BenQ的無線設備,我找她買了2台awl 700,服務不錯！
http://tw.user.bid.yahoo.com/tw/user/beaubarbara

讓大家久等了....:agree:

From: Andrew Hakman - (Repost by ) Sorry for the bad paste job, this is from cache.


NOTE ABOUT VERSION 2.2 WAP-11's: This hack can NOT be performed on the Version 2.2 WAP-11. It is based on a different chipset, and is in no way compatable with this hack. According to the spec sheet, it's 20dbm, which would work out ot 100mw anyways. BUT, linksys is getting tricky. They're counting the gain from the stock antennas as part of the power output. The real power output can be found in the FCC Registration documentation on the FCC website, which states it is 38mW. There is an interesting hack where you can load the D-Link firmware onto a WAP-11 ver 2.2 (Wap11Ver22Hack) and get it to go 22Mbps (6Mbps real world) right now, and soon 44Mbps (12Mbps real world) when D-Link releases the new ver 2.4 firmware. I've preformed this hack myself and can verify that it works! - Andrew Hakman
對VERSION 2.2 WAP 1.1使用者: 這種破解並不能施用於VERSION 2.2 WAP 1.1, 因為它們使用不同的晶片, 而且無法相容於此破解. 依照SPEC的資料, 此為 20dbm, 正因如此而不能達到100mw. 但是Linksys十分的狡猾, 他們將內存的天線當作power輸出的一部份, 而真正的power輸出是38mw, 這資料可以在FCC網站上依照FCC註冊文件內找到. 有一個十分有趣的方法就是你可以用D-Link的韌體來對 ver2.2作破解, 可以馬上達到22Mbps( 真實世界6Mbps), 而不久後D-Link會釋放新的Ver2.4韌體可達44Mbps(真實世界12Mbps), 我已經施用的這種破解而且確認成功了.

NOTE ABOUT VERSION 2.6 WAP-11's: This hack should work on the Ver 2.6's. I think I found out how to do this now. Check out the instructions at http://melbourne.wireless.org.au/wiki/?SVECWLAP Get the SNMP manager from my website: http://www.andrewhakman.dhs.org/wap11/ver26 - Andrew
對VERSION 2.6 WAP-11使用者, 此破解應可施用於VER 2.6, 我想我找到方法了, 請參看教學頁http://melbourne.wireless.org.au/wiki/?SVECWLAP , 並從這取得SNMP Manager; http://www.andrewhakman.dhs.org/wap11/ver26


Use the USB configuration utility and set your IP Address and Password. The password setting is under the "Security" tab, and then the "Password setting" button.
用USB組態設定工具去設定你的IP位址與密碼, 密碼設定在”Security”欄內, 找到後再按”Password setting”鈕


Download and Install this (http://www.andrewhakman.dhs.org/wap...g/SNMPV1743.exe). Once installed, go to c:\windows or c:\winnt (if you run nt4/2k) and find snmpmanager.ini.
下載與安裝以下檔案 http://www.andrewhakman.dhs.org/wap...g/SNMPV1743.exe , 裝好後去c:\windows或c:\winnt中找一個叫做snmpmanager.ini的檔


Edit so it looks like this: [SNMPmanager] AppMode=21 AppView=21
編輯檔案內部成這樣: [SNMPmanager] AppMode=21 AppView=21
Run the Atmel AP configurator, log into your AP using the password you previously set, and "Administrator" as the authority setting. ]
執行Atmel AP configurator, 用先前設好的密碼登入你的AP, 選Administrator


HAVE FUN - you have ALL the options, even the ones that the linksys software doesn't give you. This also gives any compatable AP (like the SMC MC2655W and the Netgear ME102) all the extra operating modes like briding and AP clinet and whatnot...
好了, 現在你擁有所有的選項了, 有些甚至是Linksys都沒有提供的, 這個破解可以適用於任何相容的AP(SMC MC2655W與NetgearME102)並提供更多的操作模式例如橋接等等


For the output power part, go to the Radio -> configuration option. All the textboxes that come up are the power output for each channel. The highest output power (100mw supposedly) is at hex value 80, and as you change the value (in either direction) from 80, the power output drops linearly (so 7A and 86 are the same power output). These settings might also explain why out of the box, performance isn't the same on all channels (with ver 1.1 hardware, certain channels have lower output power by default, with ver 1 hardware, they're all the same)!
對於power輸出部分, 去Radio選項, 選Configuration, 所有跳出的文字框表示每個頻道Power輸出, 最高的power輸出(應該是100mw)的hex值為80, 你可以從80來更改, power輸出是線性的滑落(7A與86是一樣的power輸出), 這些設定值同時可以解釋為什麼文字框外, 在各個頻道的效能並不相同(Ver1.1的硬體, 這些頻道都因預設而power輸出較低, 在Ver1.1硬體裡, 他們值全都一樣)


Use File -> download changes to send your new settings to the AP
選File->下載設定並傳輸這些新的設定值到你的AP

(optional, but FUN FUN FUN!) Using your Orinoco signal meter, actually see an increase in power output from the WAP-11 (if you have an Orinoco card that is) - you should be able to see signal of -20dbm to -27dbm easily if you are close to the WAP-11, instead of the -37dbm you normally see from 30mW devices.
(選擇性項目, 屬餘興類), 用你的Orinoco訊號表, 正確地觀察從WAP-11所增加的power輸出,(如果你有Orinoco卡的話), 當靠近Wap-11時你應該可以看到訊號從 –20dbm到-27dbm, 而不是從30mW所發出的-37dbm


(optional, but may be necessary in some cases) If you still are using OLD firmware (1.4i1 or lower), I suggest you upgrade to 1.4J1. 1.4J1 is an easy upgrade as you can do it across the network. I'm going to try to reverse engineer this and see if I can make it version independent so it can be used for flashing any version of firmware across the network. If anyone else wants to take a stab at reverse engineering it, go to it! You can get it on my website here ("http://www.andrewhakman.dhs.org/wap11/firmware/1.4j1"). Flashing the firmware will not modify the power settings.
(選擇性項目, 但有時必須去做)如果你仍使用舊的韌體(1.4i1或更低的), 我建議你升級到 1.4J1, 1.4J1可讓你很容易地升級, 我將會試試看用工程性的改變把它變成一個獨立的版本, 如此它就可以更換任何版本的韌體, 如果有任何人想要作工程性的修改, 快去做, 你可以從這裡下載 http://www.andrewhakman.dhs.org/wap11/firmware/1.4j1 , 而更換韌體並不會改變power的輸出


There must be something else that can be changed in the .ini file to allow you to actually change, _and make stick_, the operational region setting, thus you can put it in japan region, and get all 14 channels (and pump them all up to 100mw) which could allow you to run bridges in channels that don't interfer with regular access points in a really dense network, etc. With this current hack, you can change the setting, but it never sticks in the AP - once you disconnect and reconnect to it, it's back to it's usual FCC domain.
還有一些在.ini檔裡, 讓你去做其他的變更, 像操作區域等, 這樣你可以變更成日本區(Japan region), 得到14個頻道, 全部增押到100mw, 如此可讓你在頻道裡使用橋接而不會影響到正常密度網路的正規AP, 用這種破解, 你可以改變設定, 但不會纏在AP中, 一旦你中斷再重連後. 它又回歸到FCC所規定的範圍.


UPDATE: I have now figured out how to do this - e-mail me if you want to know how. ("mailto:hakmana_at_hotmail_dot_com") you'll have to fix the address. It should be obvious.
更新: 我已經交了如何做, 要知道為何這樣做, 寫信給我:


Using the SMC config program for their MC2655W (which hardware wise is identical), you can upgrade FIRMWARE ACROSS THE NETWORK via SNMP. This means that you don't need to think about USB over Ethernet (I've tried it by the way - works to ~60 feet) or physical access to the unit's USB port to do firmware updates (like if you mount it in a weather proof box on your roof!).
SMC的組態程式來對付它的MS2655W, 你可以透過 SNMP, 從網路直接升級韌體, 這表示你不需要使用到USB等東西


UPDATE: The newest firmware (1.4J1) comes with a utility to do this. Get it from my website ("http://www.andrewhakman.dhs.org/wap11/firmware/1.4j1") NOTE
更新: 最新的1.4J1韌體含工具程式可從此下載 http://www.andrewhakman.dhs.org/wap11/firmware/1.4j1


ABOUT 1.4J1 to SMC2655W users - apparantly, 1.4J1 breaks the factory reset switch functions, and because the device doesn't have a USB port, you're going to want to make sure you always remember your snmp password!
SMC2655W使用者要注意: 1.4J1已經破了還原原廠設定(RESET)的功能, 而且它沒有USB, 你千萬要記住SNMP的密碼


With the ATMEL utility, there's a program called IPConfig.exe where you EXTRACT the self extracting .exe (NOT where you install it to) that allows you to type in the MAC address and set the IP address. This is usefull in downgrading firmware (Wap11DowngradingFirmware)
ATMEL工具程式中, 有個叫做IPConfig.exe, 解開它並執行, 它可以讓你寫入mac位址並設定IP位址, 這在降級韌體程式時很有用(Wap11DowngradingFirmware )


You can find various other things on my website at ("http://www.andrewhakman.dhs.org/wap11") Have fun playing with your WAP11/SMC MC2655W/or Netgear ME102 (and others too) in all operating modes at 100mw on all channels now!
你可以在我的網站http://www.andrewhakman.dhs.org/wap11 上找到更多的東西來修改你的Wap11/SMC MC2655W/Netgear ME102, 讓它們全部的頻道都使用100mw

可以刷成linksys的機器
我刷成了
用原本的usb程式
再配上linksys的韌體就行

也就是說這台只能提升到100MW 不能 提升速度到22MBPS是嗎

中午收到機器...結果搞了一個下午...來說說心得...
1.更新韌體可以使用光碟內附的軟體...經由usb更新就可...
2.更新linksys的韌體後...千萬別用光碟內附的usb configuration util更改設定值...
去www.linksys.com下載wap11 usb configuration util來更改設定...
用光碟內的軟體更改會導致設定亂七八糟...
3.記得去設定password...不然atmel ap configuration是怎樣都連不上ap的...

另外有些疑問:
1.在snmp manager中...到底bridge ip configuration跟hardware configuration裡的mac address有什麼差別?
hardware configuration裡的可以更改...但bridge ip configuration裡的就不能更改...
但是更新其他版韌體後bridge ip configuration的mac address卻改變了?
2.可不可以推薦一下無線網路入門的討論區或介紹網站? thanx~

目前能確認的是可將功率由 38mw 大幅提升至 100mw ;
加密 64 變 128 ,增加 BRIDGE 功能.

熱心網友們提供的無線網路討論網站...大家可以參考看看,
別忘了回來分享心得喔....:)

http://www.pczone.com.tw/forumdisplay.php?forumid=76