PCDVD數位科技討論區 - P4B533-E and P4-2.26AG

PCDVD數位科技討論區 (https://www.pcdvd.com.tw/index.php)

- 效能極限 (https://www.pcdvd.com.tw/forumdisplay.php?f=18)

- - P4B533-E and P4-2.26AG (https://www.pcdvd.com.tw/showthread.php?t=115324)

Thanks to 熙, this evening I also bought a Pal8942 Heatsink with Thermaltake Fan A1214 + an Arctic Silver3 Thermal Compound totaling NT2050 from Dracular. The installation process was basically very smooth, just followed the instruction and everything is done. The quality of Pal8942 heatsink is very good due to Japanese made, and the Thermaltake fan is pretty nice, too.
Before using Pal8942, all I can get from my system is FSB160 with the Intel fan. However after adopting Pal8942, my system still can't get any further no matter how hard I have tried. I set the CPU valtage to 1.75 V and kept the Ram setting default, it just wasn't stable while running WinXP. I thought it should have gone up to at least FSB175 before I bought 8942. As a result, I think the problem is due to my poor P4-2.26AG CPU (SL683 Malay L213B370-1384, don't buy this model), it just can't overclock above FSB160.
Well, I still love my new sink and fan, they really make my computer look more powerful although it's actually not.
Thanks to 熙 again for your recommendation.
How's your new P4b533? you mentioned you would buy one too.

p.s. sorry about my poor chinese typing. (English is faster for me)

Frankiekuo

Re: To 熙 again!

引用:

Originally posted by frankiekuo
Thanks to 熙, this evening I also bought a Pal8942 Heatsink with Thermaltake Fan A1214 + an Arctic Silver3 Thermal Compound totaling NT2050 from Dracular. The installation process was basically very smooth, just followed the instruction and everything is done. The quality of Pal8942 heatsink is very good due to Japanese made, and the Thermaltake fan is pretty nice, too.
Before using Pal8942, all I can get from my system is FSB160 with the Intel fan. However after adopting Pal8942, my system still can't get any further no matter how hard I have tried. I set the CPU valtage to 1.75 V and kept the Ram setting default, it just wasn't stable while running WinXP. I thought it should have gone up to at least FSB175 before I bought 8942. As a result, I think the problem is due to my poor P4-2.26AG CPU (SL683 Malay L213B370-1384, don't buy this model), it just can't overclock above FSB160.
Well, I still love my new sink and fan, they really make my computer look more powerful although it's actually not.
Thanks to 熙 again for your recommendation.
How's your new P4b533? you mentioned you would buy one too.

p.s. sorry about my poor chinese typing. (English is faster for me)

Frankiekuo

感謝您提供的型號.....:)
我會注意的
ㄜ.....我主機板後來是買EPoX 4G4A.........(看他上面一堆sanyo電容就買了重點是很便宜...)

今天買了P4 2.26AG SL683 Malay L213B370-1390(店員直接拆盒來不及挑型號)
可以超到174MHz左右(CPU和RAM皆未加壓)
用cpu:fsb=1:1跑
ram為turbo mode
再上去沒再試了(因為溫度到60度了.....)

目前用166MHz跑.....不過待機溫度也有57度
看來ALPHA 89421壓不太住P4 2.82G......

引用:

Originally posted by 熙
今天買了P4 2.26AG SL683 Malay L213B370-1390(店員直接拆盒來不及挑型號)
可以超到174MHz左右(CPU和RAM皆未加壓)
用cpu:fsb=1:1跑
ram為turbo mode
再上去沒再試了(因為溫度到60度了.....)

目前用166MHz跑.....不過待機溫度也有57度
看來ALPHA 89421壓不太住P4 2.82G......

CPU 的體質不錯哦，恭喜！
真高興你〝無法暴走的初號機〞可以暴走了，再測一下 ELSA 525 的 3DMARK 2001 可到達幾分好嗎？因為比較少看到 ELSA 的測試，令人期待，我的配備不夠力，沒辦法讓我的 ELSA 525 跑出好成績。

引用:

Originally posted by STONESC

CPU 的體質不錯哦，恭喜！
真高興你〝無法暴走的初號機〞可以暴走了，再測一下 ELSA 525 的 3DMARK 2001 可到達幾分好嗎？因為比較少看到 ELSA 的測試，令人期待，我的配備不夠力，沒辦法讓我的 ELSA 525 跑出好成績。

顯示卡未超頻
3DMARK 2001SE預設值
2.26AG 9777
OC至2.82AG 10616
蠻遜的:(

引用:

Originally posted by 熙

顯示卡未超頻
3DMARK 2001SE預設值
2.26AG 9777
OC至2.82AG 10616
蠻遜的:(

至少比我的好，唉~
不過那也只是個數據而已，看看就好。

引用:

請問主機板和ram是那牌的,超的有夠高的

引用:

Originally posted by opalvin

請問主機板和ram是那牌的,超的有夠高的

簽名檔裡有.....:)

引用:

Originally posted by 熙
8942比腳架大了一些....左右大概寬個0.5cm吧(目測)
剛買的4G4A會有一點點卡到(應該是緊貼)一顆電容....還是可以裝(可是有點怕怕的...)
不知道P4B533會不會??

順便提供大家一個資訊，我是用ALPHA 8942M82裝在P4T-533C上面，都不會卡到電容，安裝順利。
由於電腦全日運算SETI@Home，以MBM來看CPU溫度大約在46度左右。
CPU也是P4 2.26G

熙:

看來你似乎比我好運, 你的CPU體質真棒,不加壓可上174, 真羨慕阿.